ضمن عرض سلام خدمت همه دوستان
در مرود grbl library در arduino
من یک برد uno که ماله یکی از دوستان بود رو grbl1.1 را بدون مشکل روش اپلود کردم.
الان خودم یک برد uno دگ خریدم ولی هر چه قدر تلاش می کنم grbl1.1 را نمیتونم روش بریزم. (لاگش را در پایین قرار دادم)
این موضوع در حالیه که grbl0.9 را بدون مشکل میتونم اپلود کنم. (البته با xloader)
+ blink رو اپ کردم اوکیه ، فقط با grbl1.1 مشکل داره ظاهرا.
سعی کردم خروجی hex مربوط به grbl1.1 رو با xloader اپ کنم ولی با خطای Upload failed مواجه میشم.
ممنون میشم راهنمایی کنید.
خطای ardunio 1.8.10 idea
در مرود grbl library در arduino
من یک برد uno که ماله یکی از دوستان بود رو grbl1.1 را بدون مشکل روش اپلود کردم.
الان خودم یک برد uno دگ خریدم ولی هر چه قدر تلاش می کنم grbl1.1 را نمیتونم روش بریزم. (لاگش را در پایین قرار دادم)
این موضوع در حالیه که grbl0.9 را بدون مشکل میتونم اپلود کنم. (البته با xloader)
+ blink رو اپ کردم اوکیه ، فقط با grbl1.1 مشکل داره ظاهرا.
سعی کردم خروجی hex مربوط به grbl1.1 رو با xloader اپ کنم ولی با خطای Upload failed مواجه میشم.
ممنون میشم راهنمایی کنید.
خطای ardunio 1.8.10 idea
کد:
avrdude: Version 6.3-20190619 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch System wide configuration file is "C:\Program Files (x86)\Arduino\hardware\tools\avr/etc/avrdude.conf" Using Port : COM6 Using Programmer : arduino Overriding Baud Rate : 115200 AVR Part : ATmega328P Chip Erase delay : 9000 us PAGEL : PD7 BS2 : PC2 RESET disposition : dedicated RETRY pulse : SCK serial program mode : yes parallel program mode : yes Timeout : 200 StabDelay : 100 CmdexeDelay : 25 SyncLoops : 32 ByteDelay : 0 PollIndex : 3 PollValue : 0x53 Memory Detail : Block Poll Page Polled Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- --------- eeprom 65 20 4 0 no 1024 4 0 3600 3600 0xff 0xff flash 65 6 128 0 yes 32768 128 256 4500 4500 0xff 0xff lfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 hfuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 efuse 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 lock 0 0 0 0 no 1 0 0 4500 4500 0x00 0x00 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00 Programmer Type : Arduino Description : Arduino Hardware Version: 3 Firmware Version: 4.4 Vtarget : 0.3 V Varef : 0.3 V Oscillator : 28.800 kHz SCK period : 3.3 us avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0x1e950f (probably m328p) avrdude: reading input file "C:\Users\HG\AppData\Local\Temp\arduino_build_667019/grblUpload.ino.hex" avrdude: writing flash (29762 bytes): Writing | ################################################ avrdude: stk500_paged_write(): (a) protocol error, expect=0x14, resp=0x00 avrdude: stk500_cmd(): programmer is out of sync avrdude: stk500_recv(): programmer is not responding
دیدگاه