شبیه سازی MMC در پروتیوس

[MCC]

با سلام خدمت دوستای خودم. :wow:

تو شبیه سازی MMC با نرم افزار پروتیوس به مشکل برخوردم. :angry:
میکروی من کد لازم رو به MMC میده.ولی MMC هیچ واکنشی نشون نمیده و خط ازاده.
من از یه فیل که از سایت گرفته بودم با پسوند MMC برای card image file استفاده کردم.
مشکل چیه؟
ممنون

[Mohammad6490]

پاسخ : شبیه سازی MMC در پروتیوس

سلام
فایل پروتئوس و کدهاتو بذار لطفا

[MCC]

پاسخ : شبیه سازی MMC در پروتیوس

سلام
آقا ممنون

http://www.4shared.com/file/25000224/7738d85a/mmc.html?dirPwdVerified=ba2aa578&signout=1
:biggrin:

[MCC]

پاسخ : شبیه سازی MMC در پروتیوس

اینم MMC image

http://www.4shared.com/file/25004204/ca6c2d8f/cardimage.html?dirPwdVerified=ba2aa578&signout =1

[Mohammad6490]

پاسخ : شبیه سازی MMC در پروتیوس

سلام
دوست عزیز فایل شبیه سازی پروتئوس رو هم میذاشتی :biggrin: :angry:
اگر ممکنه اونم بذار
موفق باشی

[MCC]

پاسخ : شبیه سازی MMC در پروتیوس

سلام
هر چی بود و نبود گذاشتم


http://www.4shared.com/file/25011701/b673c269/MMC.html?signout=1

[chia]

پاسخ : شبیه سازی MMC در پروتیوس

با سلام من قدیما یه کد mmc یافتم که خیلی خوب جواب داد ببین به دردت میخوره

' Program: MMC.BAS written using Bascom-AVR ver 1.11.6.2
' Basic program to interface with a Sandisk
' MMC module using the SPI protocol.
'
'         ALPHA CODE
'   **** NOT FOR COMMERCIAL USE *****
'      Ver. 0.0.9 Aug, 2001
'
' Project Reference: MMC-AT103L
' MCU: Atmel AT103L
' Software: Bascom-AVR ver 1.11.6.2
' Atmel Programmer: STK300 development board set at 3.3v.
'         ISP and terminal output
'
' Initial Date: July 23, 2001
' Projected Completion Date: Unknown
'
' Author: Ranjit Diol
'     rsdiol@compsys1.com
'     http://www.compsys1.com/workbench
'
'***************************************************************
'           (c) COMPSys, 2001
'           All Rights Reserved
'***************************************************************

'
'  DISCLAIMER: This file is being released as non-commericial
'  software. It is being provided "AS IS", neither the author,
'  nor COMPSys shall be held liable for any damages caused
'  by its use either directly or indirectly in any form or manner.
'
'===============================================================
'
'Brief: The MMC is a 3volt part therefore all data lines
'    must be conditioned if interfacing with a 5v mcu.
'    Or, a 3.3v MCU can be used such as the AT103L or the AT90LS8535
'
'IMPORTANT NOTE:
'    In SPI mode the MMC's minimum block size is 512 bytes
'    therefore data has to be accumulated first either in an eeprom
'    or in memory before sending it out as a chunk of 512 bytes.
'
'    MMC pins in SPI mode:
'      Pin1:ChipSelect(SS),Pin2:MMC input(MOSI),Pin3:GND,Pin4:3V+,
'      Pin5:Clock(SCK), Pin6:GND, Pin7:MMC output(MISO)
'    AT103L pins:
'      Portb.0 SS,Portb.1 SCK,Portb.2 MOSI, Portb.3 MISO
'
'
'==============================================================

$regfile = "m8def.dat"
$crystal = 1000000
$baud = 1200
Config Lcdpin = Pin , Db4 = Pind.6 , Db5 = Pind.2 , Db6 = Pind.3 , Db7 = Pind.4 , E = Pind.5 , Rs = Pind.7
Config Lcd = 16 * 2

Cls

'Constants
Const Msbl = 0
Const Msbh = 1
Const Dly = 2
Const Bits8 = 8
Const Bits16 = 16
Const Bits32 = 32

'Variables
Dim Res(16) As Byte
Dim Indat(512) As Byte                   'Memory buffer for temp storage.
Dim Dat As Byte
Dim Resp As Byte
Dim Resp2 As Word
Dim I As Word
Dim J As Word
Dim X As Byte
Dim Y As Byte
Dim K As Byte
Dim Bout As Byte
Dim Addr1 As Byte
Dim Addr2 As Byte
Dim Addr3 As Byte
Dim Addr4 As Byte
Dim Addr As Long
Dim Saddr As Long
Dim Eaddr As Long
Dim Fuck As Byte

'Aliases
Cs Alias Portb.0
Clk Alias Portb.1
Miso Alias Pinb.3                      'inp
Mosi Alias Portb.2                     'out

'Declarations
Declare Sub Mprint
Declare Sub Minit
Declare Sub Mstatus
Declare Sub Mwrite(byval Bout As Byte , Byval Addr As Long )
Declare Sub Mread(byval Addr As Long )
Declare Sub Merase(byval Saddr As Long , Byval Eaddr As Long)

'AT103 HW SPI Portb0=SS to MMC 1, Portb1=clock to MMC 5, MISO=Portb3 to MMC 7, MOSI=Portb2 to MMC 2

Config Pinb.0 = Output
Config Pinb.1 = Output
Config Pinb.2 = Output
Config Pinb.3 = Input
Waitms 300
Config Spi = Soft , Din = Pinb.3 , Dout = Portb.2 , Ss = Portb.4 , Clock = Portb.1

Spiinit



'******** MAIN PROGRAM *************
Main:

'Initialize the MMCC
Minit


'If you want to use the ERASE routine
'Uncomment and enter the start/end 32bit address values

'Call erase subroutine enter StartAddr , EndAddr
Merase &H00000000 , &H00000FFF


'call write subroutine as: BYTE-TO-WRITE, 32BIT_ADDRESS
'Mwrite 65 , &H00000000

'Call read sub from 512 from address are put in array INDAT
Mread &H00000000

'Call print sub print 512 bytes stored in INDAT array
Mprint


Xloop:
Set Cs
Shiftout Mosi , Clk , Dat , Msbl
Endloop:
Goto Endloop

End                             'end program
'************ END OF PROGRAM **************



'======= SUB ROUTINES AND FUNCTIONS =======

'*** INITIALIZATION OF MMC ***
Sub Minit
Set Cs
Dat = &HFF
For I = 1 To 10
 Shiftout Mosi , Clk , Dat , Msbl
Next I
Resp = 255
Reset Cs

Cmd0:
Dat = &H40
Shiftout Mosi , Clk , Dat , Msbl
Addr = &H00000000
Shiftout Mosi , Clk , Addr , Msbl
Dat = &H95
Shiftout Mosi , Clk , Dat , Msbl
While Resp <> &H01
Shiftin Miso , Clk , Resp , Msbl
Wend

Lcd "C0:" ; Hex(resp)
                    'Initialized
Set Cs
Waitms 50
Reset Cs
Dat = &HFF

Cmd1:
'While Resp <> &H00
Set Cs
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H41
Shiftout Mosi , Clk , Dat , Msbl
Addr = 0
Shiftout Mosi , Clk , Addr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
'Wend

Dat = &HFF
Set Cs
Lcd "C1:" ; Hex(resp)
End Sub

'**** READ routine assumes ADDR uses Status subroutine *****
Sub Mread(byval Addr As Long)
Set Cs
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H51
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Addr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl

While Resp <> 0
Shiftin Miso , Clk , Resp , Msbl
Wend

While Resp <> &HFE
 Shiftin Miso , Clk , Resp , Msbl
Wend

'Lcd Hex(resp)
For I = 1 To 512
  Shiftin Miso , Clk , Resp , Msbl
  Indat(i) = Resp
  'Print Hex(resp);
Next I

Shiftin Miso , Clk , Resp , Msbl
Shiftin Miso , Clk , Resp , Msbl

Set Cs
Mstatus
'Return
End Sub

'****Block Start Tag / End Tag and ERASE ****
Sub Merase(byval Saddr As Long , Byval Eaddr As Long)

'erase first 1024 bytes

'Block START TAG
Cmd32:

Set Cs
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H60
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Saddr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
While Resp <> &H00
Shiftin Miso , Clk , Resp , Msbl
Wend

'Block END TAG
Cmd33:

Set Cs
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H61
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Eaddr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
While Resp <> &H00
Shiftin Miso , Clk , Resp , Msbl
Wend

'ERASE SELECTED BLOCK
Cmd38:
Set Cs
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H66
Shiftout Mosi , Clk , Dat , Msbl
Addr = 0
Shiftout Mosi , Clk , Addr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
While Resp = 0
Shiftin Miso , Clk , Resp , Msbl
Wend

Mstatus
End Sub

'** WRITE Routine assumes ADDR, BOUT uses Status subroutine **
Sub Mwrite(byval Bout As Byte , Byval Addr As Long)
Cmd24:
Set Cs
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H58
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Addr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
While Resp <> 0
Shiftin Miso , Clk , Resp , Msbl
Wend
Lcd "C24:" ; Hex(resp)

Dat = &HFE
Shiftout Mosi , Clk , Dat , Msbl

For I = 1 To 512
 Shiftout Mosi , Clk , Fuck , Msbl
 Incr Fuck
Next I
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl

'If Y = &H05 write is a success
Y = Resp And &H0F

'If Resp = 0 the MMC is busy
Shiftin Miso , Clk , Resp , Msbl
While Resp = 0
Shiftin Miso , Clk , Resp , Msbl
Wend

Lowerline

Lcd "Wr:" ; Hex(y)
Set Cs
Mstatus
End Sub

'Get MMC Status
Sub Mstatus
Cmd13:
Set Cs
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp , Msbl
Reset Cs
Dat = &H4D
Shiftout Mosi , Clk , Dat , Msbl
Addr = 0
Shiftout Mosi , Clk , Addr , Msbl
Dat = &HFF
Shiftout Mosi , Clk , Dat , Msbl
Shiftout Mosi , Clk , Dat , Msbl
Shiftin Miso , Clk , Resp2 , Msbl
Print "Status:" ; Hex(resp2)
Set Cs
'Return
End Sub

Sub Mprint
For I = 1 To 512
Print Hex(indat(i));
Next
Mstatus
End Sub

[AMIR2]

پاسخ : شبیه سازی MMC در پروتیوس

:bye