دوستان خوبم سلام.به تازگی یک هدر برد lpc1768 خریدم.
مشکلی با هاش نداشتم که آخرین بار با تغییر کلاک CPU
این خطا رو میگیره و پروگ نمیشه.
Build target 'Flash'
assembling startup_LPC17xx.s...
compiling system_LPC17xx.c...
compiling core_cm3.c...
compiling main Prog.c...
linking...
Program Size: Code=516 RO-data=236 RW-data=16 ZI-data=608
FromELF: creating hex file...
"abgun felez.axf" - 0 Error(s), 0 Warning(s).
Load "G:\\my current project\\abgun felez\\new program\\abgun felez.AXF"
Set JLink Project File to "G:\my current project\abgun felez\new program\JLinkSettings.ini"
JLink info:
------------
DLL: V4.84c, compiled Apr 16 2014 18
07
Firmware: J-Link ARM V8 compiled Nov 25 2013 19
08
Hardware: V8.00
S/N : 58004321
Feature(s) : RDI, FlashBP, FlashDL, JFlash, GDB
* JLink Info: TotalIRLen = 4, IRPrint = 0x01
**JLink Warning: RESET (pin 15) high, but should be low. Please check target hardware.
**JLink Warning: CPU not halted after Reset, halting using Halt request
***JLink Error: Could not power up debug port: Control/Status register reads 00000F03
Load "G:\\my current project\\abgun felez\\new program\\abgun felez.AXF"
Set JLink Project File to "G:\my current project\abgun felez\new program\JLinkSettings.ini"
JLink info:
------------
DLL: V4.84c, compiled Apr 16 2014 1807
Firmware: J-Link ARM V8 compiled Nov 25 2013 1908
Hardware: V8.00
S/N : 58004321
Feature(s) : RDI, FlashBP, FlashDL, JFlash, GDB
* JLink Info: TotalIRLen = 4, IRPrint = 0x01
**JLink Warning: RESET (pin 15) high, but should be low. Please check target hardware.
**JLink Warning: CPU not halted after Reset, halting using Halt request
***JLink Error: Could not power up debug port: Control/Status register reads 00000F03
مشکلی با هاش نداشتم که آخرین بار با تغییر کلاک CPU
این خطا رو میگیره و پروگ نمیشه.
Build target 'Flash'
assembling startup_LPC17xx.s...
compiling system_LPC17xx.c...
compiling core_cm3.c...
compiling main Prog.c...
linking...
Program Size: Code=516 RO-data=236 RW-data=16 ZI-data=608
FromELF: creating hex file...
"abgun felez.axf" - 0 Error(s), 0 Warning(s).
Load "G:\\my current project\\abgun felez\\new program\\abgun felez.AXF"
Set JLink Project File to "G:\my current project\abgun felez\new program\JLinkSettings.ini"
JLink info:
------------
DLL: V4.84c, compiled Apr 16 2014 18
07Firmware: J-Link ARM V8 compiled Nov 25 2013 19
08Hardware: V8.00
S/N : 58004321
Feature(s) : RDI, FlashBP, FlashDL, JFlash, GDB
* JLink Info: TotalIRLen = 4, IRPrint = 0x01
**JLink Warning: RESET (pin 15) high, but should be low. Please check target hardware.
**JLink Warning: CPU not halted after Reset, halting using Halt request
***JLink Error: Could not power up debug port: Control/Status register reads 00000F03
Load "G:\\my current project\\abgun felez\\new program\\abgun felez.AXF"
Set JLink Project File to "G:\my current project\abgun felez\new program\JLinkSettings.ini"
JLink info:
------------
DLL: V4.84c, compiled Apr 16 2014 18
07Firmware: J-Link ARM V8 compiled Nov 25 2013 19
08Hardware: V8.00
S/N : 58004321
Feature(s) : RDI, FlashBP, FlashDL, JFlash, GDB
* JLink Info: TotalIRLen = 4, IRPrint = 0x01
**JLink Warning: RESET (pin 15) high, but should be low. Please check target hardware.
**JLink Warning: CPU not halted after Reset, halting using Halt request
***JLink Error: Could not power up debug port: Control/Status register reads 00000F03
دیدگاه