اطلاعیه

Collapse
No announcement yet.

کسی راه هایی برای تعویض آی سی های قیری داره (اصلا امکانش هست؟؟؟)

Collapse
X
 
  • فیلتر
  • زمان
  • Show
Clear All
new posts

    کسی راه هایی برای تعویض آی سی های قیری داره (اصلا امکانش هست؟؟؟)

    سلامم
    بنده قصد تعویض ـآی سی قیری یک پردازنده ی صوت usb کارمپیوتر رادارم (برای کسب تجربه)
    آیا کسی راه هایی برای تعویض این نوع میکرو ها داره ؟؟؟
    اصلا زیر این آی سی ها چه خبر هست؟؟

    #2
    پاسخ : کسی راه هایی برای تعویض آی سی های قیری داره (اصلا امکانش هست؟؟؟)

    سلام این ای سی ها قیری هستن و امکان تعویضشون نیست اگه بوردی از این ایسی استفاده کرده و خراب شده باید بورد کلا عوض بشه

    موفق باشید
    Proudly @real_ahmadi
    #real_ahmadi

    واسه اسمت بجنگ

    دیدگاه


      #3
      پاسخ : کسی راه هایی برای تعویض آی سی های قیری داره (اصلا امکانش هست؟؟؟)

      من هم همیشه واسم سوال بود
      سوال شما باعث شد برم بگردم ببینم چیه داستانش

      .That’s Chip-On-Board IC assembly technique
      .It’s been around a few decades, though with newer flip-chip assembly techniques it’ll probably start to decline
      :The chip is placed on its ‘back’, onto the surface of the PCB, and then bond-wires are attached between the contacts around the edge of the chip, and the copper pads on the PCB. Finally, a blob of quick-setting epoxy it places over the lot

      Chip-On-Board technique can save money by doing the bond-wire attachment process at your PCB assembly stage, rather than in the IC manufacturing stage (if you are manufacturing in high enough quantity - only some PCB assemblers have the equipment and expertise to do this) because you’re saving on the amount of material traditionally used to make a stand-alone chip with all its internal mounting frame, legs/pins, and surrounding epoxy. It can also save space on the PCB

      .However in the next example below, the PCB designer presumably wasn’t sure if they’d be manufacturing with Chip-On-Board, or a traditional discrete IC, so they laid out the PCB for both options, and leave the decision to later

      .So that black blob in your USB thingy pictured in your question is the IC, mounted onto the PCB via Chip-On-Board technique, that interfaces between the computer’s USB interface, and the 3.5mm audio in & out sockets

      دیدگاه


        #4
        پاسخ : کسی راه هایی برای تعویض آی سی های قیری داره (اصلا امکانش هست؟؟؟)

        البته فکر کنم با یه ترفندی بتونیم این رو کش قیری رو با چاقویی یا تیغ کاتر و .... بتراشیم و بعد میکروی زیرش رو با هویه یا هیتر عوض کنیم؟؟ (بعد با میکرو های معمولی امروزی جایگذاری کنیم پس از کد نویسی)
        چطوره بیاین امتحانش کنیم
        اگر برد رو بندازیم دور قطعات دیگرچی ؟؟ مثلا مولتی متر یکی از کاربران آی سی دیسپلیش سوخته بود (اونم قیری بود)
        شاید راه و روش هایی جز دور انداختن برد باشه
        نظر شما چیه؟؟

        دیدگاه

        لطفا صبر کنید...
        X