من میآخوام 60 تا LED RGB رو درایو کنم. البته همهآی 60 تا LED همزمان روشن نیستن و نهایتا 5 تاشون همزمان روشن هستن.
بهترین روش برای این کار چیه؟
بهترین روش برای این کار چیه؟
#include <mega16.h> #include <delay.h> unsigned int counter=0; unsigned char value1=0,value2=0,value3=0,value4=0,value5=0,value6=0,value7=0,value8=0; // Timer 0 overflow interrupt service routine interrupt [TIM0_OVF] void timer0_ovf_isr(void) { // Place your code here counter++; if(counter>=20) { counter=0; PORTD=0xff; } if(counter==value1)PORTD.0=0; if(counter==value2)PORTD.1=0; if(counter==value3)PORTD.2=0; if(counter==value4)PORTD.3=0; if(counter==value5)PORTD.4=0; if(counter==value6)PORTD.5=0; if(counter==value7)PORTD.6=0; if(counter==value8)PORTD.7=0; //TCNT0=20; } // Declare your global variables here void main(void) { // Declare your local variables here // Input/Output Ports initialization // Port A initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTA=0x00; DDRA=0xff; // Port B initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTB=0x00; DDRB=0x00; // Port C initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTC=0x00; DDRC=0x00; // Port D initialization // Func7=In Func6=In Func5=In Func4=In Func3=In Func2=In Func1=In Func0=In // State7=T State6=T State5=T State4=T State3=T State2=T State1=T State0=T PORTD=0x00; DDRD=0xff; // Timer/Counter 0 initialization // Clock source: System Clock // Clock value: 1000.000 kHz // Mode: Normal top=FFh // OC0 output: Disconnected TCCR0=0x01; TCNT0=0x00; OCR0=0x00; // Timer/Counter 1 initialization // Clock source: System Clock // Clock value: Timer 1 Stopped // Mode: Normal top=FFFFh // OC1A output: Discon. // OC1B output: Discon. // Noise Canceler: Off // Input Capture on Falling Edge TCCR1A=0x00; TCCR1B=0x00; TCNT1H=0x00; TCNT1L=0x00; ICR1H=0x00; ICR1L=0x00; OCR1AH=0x00; OCR1AL=0x00; OCR1BH=0x00; OCR1BL=0x00; // Timer/Counter 2 initialization // Clock source: System Clock // Clock value: Timer 2 Stopped // Mode: Normal top=FFh // OC2 output: Disconnected ASSR=0x00; TCCR2=0x00; TCNT2=0x00; OCR2=0x00; // External Interrupt(s) initialization // INT0: Off // INT1: Off // INT2: Off MCUCR=0x00; MCUCSR=0x00; // Timer(s)/Counter(s) Interrupt(s) initialization TIMSK=0x01; // Analog Comparator initialization // Analog Comparator: Off // Analog Comparator Input Capture by Timer/Counter 1: Off // Analog Comparator Output: Off ACSR=0x80; SFIOR=0x00; // Global enable interrupts #asm("sei") while (1) { value1=5; value2=10; value3=4; value4=3; value5=15; value6=6; value7=9; value8=20; // PORTD.0=0; // delay_ms(2000); // PORTD.0=1; // delay_ms(2000); // Place your code here }; }
دیدگاه