دوستان گرامی من این اقلام رو در خانه دارم به تازگی ماژول آمپلی فایر هم به دستم رسیده. می خواستم اگر ممکنه راهنمایی کنید که من بتونم حداکثر قدرت رو از این ماژول دریافت کنم. چیزهایی که در خانه دارم این موارد هست:
1- ماژول آمپلی فایر 600 وات 300+300 مدل TAS5630 4 Ohm Class D
2- دو عدد ساب ووفر 12 اینچ هکتور 2 کویل؟
3- یک عدد فیلتر پایین گذر چیستا ( لازم هست اصلا روی این ماژول؟ )
4- یک عدد ترانس 50 ولت 20 آمپر دوبل AC که البته می تونیم تبدیلش کنیم به دو عدد ترانس 50 ولت 10 آمپر تک ( باید ولتاژ به DC تبدیل بشه چطور؟ )
الان راه اندازی ساب ووفر با این موارد ممکن هست؟ چه مواردی باید تغییر کنه یا برای شروع راه اندازیو نصب باید چه کارهایی انجام بدم؟ ولتاژ منبع تغذیه دقیقا در بهترین حالت باید چند باشه؟ چون الان توی سایت های مختلف اعداد متفاوتی درج کردند. 48 یا 50؟
تصویر ساب ووفر 12 اینچ هکتور که 2 عدد موجود هست:
تصویر ماژول امپلی فایر :
_thumb.jpeg)
_thumb.jpeg)
دلیل: ادغام دو پست برای جلوگیری از اسپم
لینک مشخصات ماژول آمپلی فایر که فکر کنم دقیقا ظاهرش همین باشه:
Sure Electronics AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
دلیل: ادغام دو پست برای جلوگیری از اسپم
مشخصات دیگری که در این سفحه درباره ماژول آمپلی فایر درج شده:
Specifications for: AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
2 300 watts at 4 ohms
Minimum load
3.5 ohms
Efficiency
91 - 96 %
Signal-to-noise ratio (SNR)
89 dB
Distortion
0.07 % THD at 4 ohms, 1 watt, 1 kHz
0.028 % THD at 4 ohms, 10 watts, 1 kHz
View all specifications
Frequency response 20 - 20,000 Hz
Gain 28 - 32 dB
Input sensitivity 1.2 V
Input impedance 10k ohms
Amplifier Classification Class D
Circuit Topology Texas Instruments TAS5630
Speaker output channels 2
Input connection type RCA
Speaker output connection type Screw terminals
PCB solder connector
DSP function -
Bluetooth -
EQ Adjustment -
Power Requirements 55 - 65 VDC
Power inlet connector Screw terminals
DC jack 5.5 / 2.5mm
Current limit 13.5 A
Under/over voltage protection
Dimensions (L x W x H) 121.92 x 91.44 x 38.86 mm
Mounting hole spacing -
Mounting hole diameter 3.8 mm
---------------
سایت بعدی اینجوری نوشته
AA-AB32195 - 2 x 300W @4ohm TAS5630 - Audio Amplifier Board - Sure Electronics
Here comes the2 x 300Watt amplifier board,AA-AB32195.
This audio amplifier board employs Sure Electronics T-AMP technology, featuring low distortion and low noise level.
Hear your music like never before with 300 Watts per channel of audiophile-grade Tripath Class-T technology. Amp includes a quiet running fan to keep things cool.
This amplifier board supports stereo (dual) amplification by using two channel PBTL topology.
By means of dedicated heat sink design with temperature controlled fan，it is capable of delivering dual channel maximum power 300W RMS @ 3ohm simultaneously without extraordinary heat sink.
Besides of built-in chip protection, ESD and spike protection components used throughout input and output of the amplifier board ensure its robustness and reliability.
This amplifier board supports mono amplification by using PBTL topology.
Fan works when the temperature of heatsink reaches up to 45 degrees Celsius and stops when the temperature reduces down to 40 degrees Celsius.
So the audible noise and idle power loss brought by fan could be omitted when output RMS power is moderate.
Features:
Application:
Electrical Specifications：
Specifications typical @ +25℃, Powered by 48V DC, unless otherwise noted. Specifications subject
to change without notice.
Audio Performance:
Specifications typical @ +25℃, Powered by 40V DC, unless otherwise noted. Specifications subject
to change without notice.
1- ماژول آمپلی فایر 600 وات 300+300 مدل TAS5630 4 Ohm Class D
2- دو عدد ساب ووفر 12 اینچ هکتور 2 کویل؟
3- یک عدد فیلتر پایین گذر چیستا ( لازم هست اصلا روی این ماژول؟ )
4- یک عدد ترانس 50 ولت 20 آمپر دوبل AC که البته می تونیم تبدیلش کنیم به دو عدد ترانس 50 ولت 10 آمپر تک ( باید ولتاژ به DC تبدیل بشه چطور؟ )
الان راه اندازی ساب ووفر با این موارد ممکن هست؟ چه مواردی باید تغییر کنه یا برای شروع راه اندازیو نصب باید چه کارهایی انجام بدم؟ ولتاژ منبع تغذیه دقیقا در بهترین حالت باید چند باشه؟ چون الان توی سایت های مختلف اعداد متفاوتی درج کردند. 48 یا 50؟
تصویر ساب ووفر 12 اینچ هکتور که 2 عدد موجود هست:
تصویر ماژول امپلی فایر :
.jpeg)
.jpeg)
دلیل: ادغام دو پست برای جلوگیری از اسپم
لینک مشخصات ماژول آمپلی فایر که فکر کنم دقیقا ظاهرش همین باشه:
Sure Electronics AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
This is the upgraded version of the original 2 X 300 watt TAS5630 class D audio amplifier board.
This amplifier board supports stereo amplification by using two channel PBTL topology. By means of dedicated heat sink design with
Sure Electronics AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
This is the upgraded version of the original 2 X 300 watt TAS5630 class D audio amplifier board.
This amplifier board supports stereo amplification by using two channel PBTL topology. By means of dedicated heat sink design with temperature controlled fan, it is capable of delivering dual channel maximum power 300W RMS @ 4ohm simultaneously without extraordinary heat sink.
Highlights
Product Details
Sure Electronics AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
Tip: Take a look at the table in this blogpost to see which power supply to choose for this product.
Introducing Sure Electronics new compact 2x300W audio amplifier board with audiophile-grade TAS5630. Amp includes a quiet running fan to keep things cool. It inherits its original high performance basis, including support for dual channel simultaneous outputting 300W RMS @ 4Ohm, low THD+N, high SNR, powering up with music signal input. The most significant change is the reduction in size down to 4.8inch X 3.6inch X 1.8inch, which improves the power density and help space saving in design of audio playback system. Besides that, the function of temperature control fan is also introduced. Fan works when the temperature of heatsink reaches up to 45 degrees Celsius and stops when the temperature reduces down to 40 degrees Celsius.
temperature controlled fan
This amplifier board supports stereo amplification by using two channel PBTL topology. By means of dedicated heat sink design with
Sure Electronics AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
This is the upgraded version of the original 2 X 300 watt TAS5630 class D audio amplifier board.
This amplifier board supports stereo amplification by using two channel PBTL topology. By means of dedicated heat sink design with temperature controlled fan, it is capable of delivering dual channel maximum power 300W RMS @ 4ohm simultaneously without extraordinary heat sink.
Highlights
- Excellent heatsink performance
- Capable of 2x300W RMS output @ 4 Ohm
- Requires 55 to 65 VDC power supply
- Size：8 inch x 3.6 inch x 1.8 inch
- Under voltage protection
- Over current protection
- Short circuit and over temperature protection
Product Details
Sure Electronics AA-AB32192 2x300W TAS5630 4 Ohm Class D Audio Amplifier Board Compact
Tip: Take a look at the table in this blogpost to see which power supply to choose for this product.
Introducing Sure Electronics new compact 2x300W audio amplifier board with audiophile-grade TAS5630. Amp includes a quiet running fan to keep things cool. It inherits its original high performance basis, including support for dual channel simultaneous outputting 300W RMS @ 4Ohm, low THD+N, high SNR, powering up with music signal input. The most significant change is the reduction in size down to 4.8inch X 3.6inch X 1.8inch, which improves the power density and help space saving in design of audio playback system. Besides that, the function of temperature control fan is also introduced. Fan works when the temperature of heatsink reaches up to 45 degrees Celsius and stops when the temperature reduces down to 40 degrees Celsius.
temperature controlled fan
دلیل: ادغام دو پست برای جلوگیری از اسپم
مشخصات دیگری که در این سفحه درباره ماژول آمپلی فایر درج شده:
- [*=left]Rated power output (RMS)
2 300 watts at 4 ohms
Minimum load
3.5 ohms
Efficiency
91 - 96 %
Signal-to-noise ratio (SNR)
89 dB
Distortion
0.07 % THD at 4 ohms, 1 watt, 1 kHz
0.028 % THD at 4 ohms, 10 watts, 1 kHz
View all specifications
Frequency response 20 - 20,000 Hz
Gain 28 - 32 dB
Input sensitivity 1.2 V
Input impedance 10k ohms
Amplifier Classification Class D
Circuit Topology Texas Instruments TAS5630
Speaker output channels 2
Input connection type RCA
Speaker output connection type Screw terminals
PCB solder connector
DSP function -
Bluetooth -
EQ Adjustment -
Power Requirements 55 - 65 VDC
Power inlet connector Screw terminals
DC jack 5.5 / 2.5mm
Current limit 13.5 A
Under/over voltage protection
Dimensions (L x W x H) 121.92 x 91.44 x 38.86 mm
Mounting hole spacing -
Mounting hole diameter 3.8 mm
---------------
سایت بعدی اینجوری نوشته
AA-AB32195 - 2 x 300W @4ohm TAS5630 - Audio Amplifier Board - Sure Electronics
Here comes the2 x 300Watt amplifier board,AA-AB32195.
This audio amplifier board employs Sure Electronics T-AMP technology, featuring low distortion and low noise level.
Hear your music like never before with 300 Watts per channel of audiophile-grade Tripath Class-T technology. Amp includes a quiet running fan to keep things cool.
This amplifier board supports stereo (dual) amplification by using two channel PBTL topology.
By means of dedicated heat sink design with temperature controlled fan，it is capable of delivering dual channel maximum power 300W RMS @ 3ohm simultaneously without extraordinary heat sink.
Besides of built-in chip protection, ESD and spike protection components used throughout input and output of the amplifier board ensure its robustness and reliability.
This amplifier board supports mono amplification by using PBTL topology.
Fan works when the temperature of heatsink reaches up to 45 degrees Celsius and stops when the temperature reduces down to 40 degrees Celsius.
So the audible noise and idle power loss brought by fan could be omitted when output RMS power is moderate.
Features:
- 2mm PCB thickness，2OzCu
- Support adjusting volume on board with a additional module
- Screwing to chassis conveniently
- Can be shut down easily by external pulled down to GND
- Excellent heatsink performance
- Size：4.8inchX3.6inchX1.53inch
- weight：290g
- Under voltage and over voltage protection
- Over current protection
- Short circuit and over temperature protection
- Analog single ended signal input
- Output 300W@3ohm 48V DC THD+N 10%
206W@3ohm 48V DC THD+N 1%
Application:
- Home theater receiver
- Car audio
- Background music systems
- Musical instrument amplifiers
- Prototype for recording studios, Post-production, Live sound and Hi-Fi applications
Electrical Specifications：
Specifications typical @ +25℃, Powered by 48V DC, unless otherwise noted. Specifications subject
to change without notice.
| Parameter | Conditions | Min. | Typ. | Max. | Units |
| Power Supply | - | 15 | 48 | 50 | VDC |
| Idle Power | SD Floating,FAN ON | - | 9.6 | 18 | W |
| SD Floating,FAN OFF | - | 8 | 15 | W | |
| Standby Power | SD Connected to GND,FAN OFF | - | 0.8 | 5 | W |
| Maximum Current | 600W @3Ohm | - | 14.2 | - | A |
| Efficiency | 300W @3Ohm | 86 | - | 91 | % |
| Minimum Load Impedance | - | - | 3 | - | Ω |
| Switching Frequency | SD Floating | - | 674 | - | KHz |
| Fan Active @ Temperature | - | - | 50 | - | ℃ |
Specifications typical @ +25℃, Powered by 40V DC, unless otherwise noted. Specifications subject
to change without notice.
| Parameter | Conditions | Min. | Typ. | Max. | Units |
| Gain | - | 26 | 28 | 30 | dB |
| Input Sensitivity(RMS) | @3Ω, 300W,1KHz | - | 917 | - | mV |
| Input Impedance | - | - | 33 | - | KΩ |
| Output Power | @3Ω THD+N 1% | - | 206 | - | W |
| @3Ω THD+N 10% | - | 300 | - | W | |
| Bandwidth @ ±3dB | @3Ω | 20 | - | 20K | Hz |
| THD | @3Ω, 1W, 1KHz | - | 0.0052 | - | % |
| @3Ω, 10W, 1KHz | - | 0.025 | - | % | |
| Output Noise Level | A-weighting,Input Connected to GND | - | 209 | - | µV |
| SNR | 206W @3Ω THD+N 1% | - | 94.8 | - | dB |
دیدگاه